Tube Key Fitting test page

Tube Key Fittings

The Short Tee provides a 90° butt joint between two pipes, ideal for connecting end uprights to a middle rail.

Key Fitting Short Tee (101)

The Long Tee creates a 90° butt joint, allowing the through pipe to pass inside the fitting—ideal for connecting a top rail to an intermediate upright.

Key Fitting Long Tee (104)

The 3 Way Open Corner fitting is designed for creating corner joints in mid-rails of handrails, guardrails, or frames.

Key Fetting 3 Way Open Corner (116)

The Short Cross fitting is used for forming middle rail joints in handrails and similar structures, with the center pipe passing through unjoined.

Key Fitting Socket Cross (119)

The Variable Elbow allows angled joints between 105° and 165°, ideal for custom angles in railings or frames.

Key Fitting Varriable Elbow (124)

The 90 Degree Elbow forms a right-angle joint between two pipes, commonly used for railing ends or corners in level installations.

Key Fitting 2 Way Elbow 90 Deg. (125)

This hollow fitting is designed for use with rubber or polyamide hoses of custom inner diameters .

Key Fetting 3 Way Blind Corner (128)

The Variable Angle Tee connects top rails to end uprights on slopes ranging from 30° to 60°, ideal for angled tee joints. Suitable for handrails on stairs or sloped surfaces.

ADJUSTABLE TEE PIPE CLAMPS (129)

The Base Flange is used for positional wall or base fixing but is not recommended as a railing base. Available in 27mm to 60mm pipe sizes .

Key Fetting Round Base Flange (131)

The Square Base Flange allows the pipe to pass through while providing a positional wall or base fixing, though not recommended for railing bases.

Key Fitting Square Base Flange (S131)

The Railing Base Flange offers strong structural fixing for guardrails and balustrades, with holes suitable for mechanical or chemical anchors.

Key Fetting Railing Base Flange (132)

This is a plastic cap that plugs the end of the tube.

PIPE END PLUG ( PLASTIC) (133)

The Ground Support fitting is designed to be cast into the ground to support a removable post. Available in 27mm to 60mm pipe sizes.

Key Fitting Ground Support (134)

The Clamp On Tee allows new pipes to be added to existing structures, making design modifications simple and efficient.

Key Fitting Clamp on Tee (135)

This is a plastic cap that plugs the end of the tube.

PIPE END PLUG (STEEL) (136)

The Gate Eye, used with EF32, serves as the female hinge component for lightweight gates. For heavier gates, use EF03 with EF30 for enhanced support.

GATE EYE GATE EYE PIPE CLAMPS (138)

The Gate Hinge, paired with EF31, functions as the male hinge part for lightweight gates. For heavy-duty gate.

GATE HINGE GATE HINGE PIPE CLAMPS (140)

The Rail Bracket is used to secure handrail pipes to a wall or the top of a wall for lower rail support; pipes cannot be joined within the fitting.

Key Fitting Rail Support (143)

The Vertical Base Flange provides a side-mounted base fitting for railings where the upright does not pass through the fitting.

Key Fitting Railing Veryical Side Support (144)

This coupling is designed for fixing railings and railings to walls, bridges or stairs.

HORIZONTAL RAILING SIDE SUPPORT (145)

The Wall Flange is a side-mounted base fitting for railings where the upright cannot pass through the fitting.

Key Fitting Wall Flange (Side Palm Fix) (146)

The Internal Swivel Tee allows for angled joints between a rail and an Easyfit fitting, ideal for offsetting top or mid rails on slopes.

Internal Swivel Short Tee (147)

The Short Tee Swivel is designed to provide corner joints with angles varying from 90 to 180 degrees. Sold in pairs.

SHORT SWIVEL TEE-PAIR (148)

The Straight Sleeve creates an inline joint between two same-size pipes, maintaining alignment. For a constant outer diameter, use EF01 expanding connector.

Key Fitting Straight Sleevs (149)

This internal connector provides an almost smooth joint between two same-diameter tubes. It offers lower clamping force than type 149 and is not suitable for load-bearing applications.

INTERNAL TUBE CONNECTOR (150)

The 4 Way With Center Pipe fitting creates a four-way connection around an upright; the center pipe cannot pass through but can end inside and be capped with an EF65.

Key Fetting 4 way Cross (158)

The Clamping Cross Over creates a 90-degree crossover joint, ideal for building or extending railings, racks, and other structures. Perfect for adding onto existing pipe frameworks.

Key Fitting Clamping Crossover (160)

The Cross Over fitting connects two offset pipes at 90 degrees, commonly used in shelf or pallet racking to join horizontal rails to uprights. Pipes cannot be joined within the fitting.

Key Fitting Offset Crossover (161)

This fitting combines a socket tee and crossover, joining horizontal rails to an upright while allowing a perpendicular horizontal tie.

Key Fitting Combination Socket (165)

The Double Swivel Kit combines two EF36 Single Female Swivels with an EF37 Double Male Swivel to form an inline angled joint at a post.

Key Fitting Double Swivel Kit (167)

The male part of combination coupling type 167, this fitting is commonly used to fix panels or add angled struts for structural support without dismantling.

DOUBLE SWIVEL SOCKET MAIL (167M)

The 90 Degree Corner Swivel Kit includes two EF36 Single Female Swivels and one EF38 90° Corner Male Swivel, joined with bolts, nuts, and washers.

Key Fitting Corner Swivel Kit (168)

The Corner Male Swivel fitting, secured with steel bolts, nuts, and washers, provides an angled joint at a post. It supports possible reducer combinations in sizes DA1 to DE5 with 173F

CORNER SWIVEL SOCKET MALE (168M)

The Base Swivel Kit includes a Single Female Swivel and a Swivel Base, joined with a stainless steel bolt, nut, and washers. I

Key Fitting Base Swivel Kit (169)

The Swivel Base, used with an EF36 Female Swivel to form an EF46 Swivel Base Kit, is ideal for bracing or wall mounting where structural rigidity is not critical.

Key Fetting Swivel Base (169M)

The Single Sided Clamp secures mesh panels to one side of a vertical or horizontal tube and is supplied with an M6x30mm bolt and nut.

Single Side Mesh Clamp (170)

This fitting is designed to attach mesh panels to both sides of a tube and can also secure sheet materials like board when used without the return piece.

Double Side Mesh Clamp (171)

This complete combination fitting is designed for angled support and bracing within structures. Reducing combinations are available .

SINGLE SWIVEL SOCKET (173)

The Female Swivel is used with EF10, EF35, EF37, and EF38 to create Swivel Kits, ideal for bracing and handling joints at odd or varying angles.

Key Fitting Swivel Female (173F)

The Male Swivel is used with EF36 and EF41 to form a combination fitting that adds an angled strut for supporting existing structures without dismantling.

MALE SWIVEL (173M)

The Side Outlet Tee creates a three-way joint for handrails and similar structures, with the center pipe unable to pass through the fitting. Available in 27mm to 60mm.

Key Fetting side Outlet Tee (176)

The Collar serves as a support fitting for an EF03 when used as a hinge and can also enhance the load capacity of other fittings.

COLLAR (179)

The Hook is designed to provide attachment for a chain

HOOK (182)

"The Hook is designed to provide attachment for a chain and.

HOOK STRAIGHT (183)

These pipe couplings have been developed to mount panels in pipe constructions, among other things.

FIXING PAD ( DOUBLE) (198)

The Fixing Pad allows secure attachment of flat panels made of lightweight metal, plastic, or wood—ideal for backing or flooring on pipe structures.

FIXING PAD (SINGLE) (199)

The Fixing Pad is designed to attach flat panels of lightweight metal, plastic, or wood—such as backing or flooring—to pipe structures.

FIXING PAD (199)

About Us

At Bhagat Impex, we specialize in the export of high-quality goods with a focus on reliability, integrity, and global standards. Our commitment to excellence has earned us the trust of partners worldwide.