Round Tube Key Fittings

The Short Tee is designed to provide a butt joint between two pipes at right angles to each other. Often used to join end uprights to the middle rail on a level installation. If two pipes need to be joined inside the fitting, an EF04 should be used. This kee clamp fittings available in pipe outer size 60mm to 27mm ( as per standard) or as per custmer need with hot dip galvanizing, powder coating any colour and zinc plating

The Long Tee is designed to provide a butt joint between two pipes at right angles to each other. It allows the through pipe to be joined inside the fitting, and is an alternative to EF03. Often used as to connect the top rail to an intermediate upright in a level installation. This kee clamp fittings available in pipe outer size 60mm to 27mm ( as per standard) or as per custmer need with hot dip galvanizing,powder coating any colour and zinc plating.

The 3 Way Open Corner, with its through hole, is designed as a corner fitting for a middle rail of handrails, guardrails or frames. This kee clamp fittings available in pipe outer size 60mm to 27mm ( as per standard) or as per custmer need with hot dip galvanizing,powder coating any colour and zinc plating

The Short Cross is designed as a middle rail joint for handrail and other structures. The center pipe cannot be joined inside the fitting. This kee clamp fittings available in pipe outer size 60mm to 27mm ( as per standard) or as per custmer need with hot dip galvanizing,powder coating any colour and zinc plating

The Variable Elbow is designed to make joints at an angle of between 105° and 165° This kee clamp fittings available in pipe outer size 60mm to 27mm ( as per standard) or as per custmer need with hot dip galvanizing,powder coating any colour and zinc plating.

The 90 Degree Elbow is designed to provide a joint between two pipes at right angles to each other. It is often used as railing ends or corners on a level installation. This kee clamp fittings available in pipe outer size 60mm to 27mm ( as per standard) or as per custmer need with hot dip galvanizing,powder coating any colour and zinc plating.

To be used with a rubber or polyamid hose that has an inside diameter as per cstomer demand. This hollow fitting has an inside flow hole used for high pressure applications. This fitting may come in zinc or yellow zinc plated finishes.

The Variable Angle Tee is designed to fasten top rails to end uprights on slopes from 30 to 60 degrees, or any tee joint requiring this range of angle.

The Base Flange is designed to provide a positional wall or base fixing. It is not recommended to use this fitting as a railing base. This kee clamp fittings available in pipe outer size 60mm to 27mm ( as per standard) or as per custmer need with hot dip galvanizing, powder coating any colour and zinc plating.

The Railing Base Flange is designed to provide structural fixing to guardrail and balustrades. The holes are sufficient diameter to provide good fixing with either mechanical or chemical anchors, and should be used in accordance with the Easy fit Maximum Post Center Table # 3 located on the Resources Page. This kee clamp fittings available in pipe outer size 60mm to 27mm ( as per standard) or as per custmer need with hot dip galvanizing, powder coating any colour and zinc plating.

This is a plastic cap that plugs the end of the tube.

The Ground Support is designed to provide a base that can be cast into the ground to support a post. The post is removable. This kee clamp fittings available in pipe outer size 60mm to 27mm ( as per standard) or as per customer need with hot dip galvanizing, powder coating any colour and zinc plating.

The Clamp On Tee is designed to allow new pipe to be joined to an existing structure and allows easy modification of design. Can be used in combination with fittings EF36G and EFG36M.

The Gate Eye, used in conjunction with EF32, is designed as the female section of a hinge for a lightweight gate.

The Gate Hinge, used in conjunction with EF31, is designed as the male section of a hinge for a lightweight gate. For heavier gate installations, an EF03 in conjunction with an EF30 is recommended.

The Rail Bracket is designed to secure handrail pipe to a wall. It can also be used on the top of a wall to secure a lower rail. Pipes cannot be joined inside this fitting. This kee clamp fittings available in pipe outer size 60mm to 27mm ( as per standard) or as per custmer need with hot dip galvanizing, powder coating any colour and zinc plating.

The Vertical Base Flange is designed to provide a base fitting for railings requiring a side mounted fixing. The upright cannot pass through the fitting. It should be used in accordance with Easyfit Maximum Post Center Table # 3 located on the Resources Page. This kee clamp fittings available in pipe outer size 60mm to 27mm ( as per standard) or as per custmer need with hot dip galvanizing, powder coating any colour and zinc plating.

This coupling is designed for fixing railings and railings to walls, bridges or stairs.

The Wall Flange is designed to provide a base fitting for railings requiring a side mounted fixing. The upright cannot pass through the fitting. It should be used in accordance with Easyfit Maximum Post Center Table # 3 located on the Resources Page. This kee clamp fittings available in pipe outer size 60mm to 27mm ( as per standard) or as per custmer need with hot dip galvanizing, powder coating any colour and zinc plating.

The Internal Swivel Tee is designed to accommodate varying angles in a joint between a rail and an Easy fit fitting. Often used in conjunction with EF02 or EF03 type fittings to offset the top or mid rail to accommodate slopes. This kee clamp fittings available in pipe outer size 60mm to 27mm ( as per standard) or as per custmer need with hot dip galvanizing, powder coating any colour and zinc plating.

The Short Tee Swivel is designed to provide corner joints with angles varying from 90 to 180 degrees. Sold in pairs.

The Straight Sleeve is designed to provide an inline joint between two pieces of pipe of the same size. Where a constant diameter is required along the outside of the pipe, use EF01, an expanding connector. This kee clamp fittings available in pipe outer size 60mm to 27mm ( as per standard) or as per custmer need with hot dip galvanizing, powder coating any colour and zinc plating.

This is an internal connection that makes an (almost) smooth connection between two tubes with the same diameter. This coupling has less clamping force than type 149 and can therefore not be used in places where there is a direct load on the coupling.

The 4 Way With Center Pipe is designed to provide a four way connection to an upright. The center pipe cannot be joined inside the fitting, but it can end inside the fitting and be capped using an EF65. This kee clamp fittings available in pipe outer size 60mm to 27mm ( as per standard) or as per custmer need with hot dip galvanizing, powder coating any colour and zinc plating.

The Clamping Cross Over provides a 90-degree crossover joint to build railings, racks, and more. Although the EF42 crossover fitting can be used to build original new structures, it is ideally suited for adding on to existing pipe structures.

The Cross Over fitting is designed to fasten two pipes at 90 degrees to each other and off set. Used for shelf or pallet racking to join horizontal carrying rails to the uprights. Pipes cannot be joined inside the fitting.

Serves as a combination socket tee and crossover by joining horizontal rails to an upright, leaving the protruded socket to take a horizontal tie, perpendicular to the other rails, across the section. This makes it ideal for building shelved racks (with the horizontal pipe outside the upright), or pallet racks (horizontal pipe inside the upright.

The Double Swivel Kit is composed of two EF36 Single Female Swivel fittings connected to an EF37 Double Male Swivel fitting with steel bolts, nuts and washers. It is designed to provide an in line angle joint at a post. This kit can be used to fasten middle rails to uprights in sloping handrail installations, or to provide bracing to a structure. Hardware (nuts, bolts, washers) is included.

Male part of the combination coupling type 167. This coupling is also often used for fixing panels and provide an angled strut to support an existing structure without dismantling. It can also be used to provide attachment of flat panels of lightweight metal, plastic or wood to pipe structures.

The 90 Degree Corner Swivel Kit is composed of two EF36 Single Female Swivel fittings connected to an EF38 90 Degree Corner Male Swivel fittings using steel bolts, nuts and washers. It is designed to provide an angled joint at a post. This kit can be used to fasten middle rails to uprights in sloping handrail installations, or to provide bracing to a structure. Hardware (bolts, nuts, washers) is included.

Corner Male Swivel fittings using steel bolts, nuts and washers. It is designed to provide an angled joint at a post and Possible Reducer combinations are also possible in sizes DA1 to DE5 with 173F.It can also be used to provide attachment of flat panels of lightweight metal, plastic or wood to pipe structures.

The Base Swivel Kit is composed of an Single Female Swivel connected to Swivel Base with a stainless steel bolt, nut and washers. It is designed to serve as a variable angle wall or floor mounting. This kit should not be used as a railing base without suitable support. Hardware (nut, bolt, washers) is included.

The Swivel Base is designed to be used in combination with an EF36 (female) fitting to make an EF46 Swivel Base Kit. Often used as a brace or wall fitting when structural rigidity is not at issue. This kee clamp fittings available in pipe outer size 60mm to 27mm ( as per standard) or as per custmer need with hot dip galvanizing, powder coating any colour and zinc plating

Complete combination fitting. Reducing combinations are available sizes DA1 through DE5. to make support to at angle and bracing in the structure.

The Female Swivel is designed to be used in combination with EF10, EF35, EF37, and EF38 to make “Swivel Kits” used primarily for bracing, but can also be used to overcome problems with joints of odd or varying angles. It can also be used to secure infill of sheets of lightweight metal, plastic or wood to pipe structures.

The Male Swivel designed to be used in combination with an EF36 and an EF41 to create a combination fitting that will provide an angled strut to support an existing structure without dismantling. It can also be used to provide attachment of flat panels of lightweight metal, plastic or wood to pipe structures.

The Collar is designed to be used as a support fitting for an EF03 when it is used as a hinge. It can be used to increase the load capacity of another fitting or as a stop on a telescoping pipe or tube.

The Hook is designed to provide attachment for a chain.

These pipe couplings have been developed to mount panels in pipe constructions, among other things.

The Fixing Pad is designed to provide attachment of flat panels of lightweight metal, plastic or wood such as backing or flooring to pipe structures. It may also be used as a gate stop.

About Us

At Bhagat Impex, we specialize in the export of high-quality goods with a focus on reliability, integrity, and global standards. Our commitment to excellence has earned us the trust of partners worldwide.

Round Tube Key Fittings

About Us

Address List

Quick Links